View EP5358LUA_8961680.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

enpirion ? power datasheet EP5358LUA/hua 600ma powersoc voltage mode synchronous pwm buck with integrated inductor www.altera.com/enpirion description the ep5 358lua and ep5358hua are 600m a powersoc s that are aec - q100 qualified for automotive applications . the ep5358x ua (x = l or h) is rated for up to 600ma of continuous output current. the ep5358x ua integrates mosfet switches, control, compensation, and the magnetics in an advanced 2.5mm x 2.25mm micro - qfn package. integrated magnetics enables a tiny solution footprint , low output ripple, low part - count, and high reliability, while maintaining high efficiency. the complete solution can be implemented in as little as 14mm 2 . the ep5358x ua uses a 3 - pin vid to easily select the output voltage setting. output voltage settings are available in 2 optimized ranges providing coverage for typical v out settings. the vid pins can be changed on the fly for fast dynamic voltage scaling. ep5358l ua further has the option to use an external voltage divider. the ep5358x ua is a perfec t solution for noise sensitive and space constrained applications that require high efficiency. features ? integrated inductor technology ? - 40c to + 105c ambient temperature range ? aec - q100 qualified for automotive applications ? 2.5mm x 2.25mm x 1.1mm uqfn p ackage ? total solution footprint 14mm 2 ? low v out r ipple for rf c ompatibility ? high efficiency, up to 93% ? up to 600ma c ontinuous o utput c urrent ? 5 mhz s witching f requency ? 3 pin vid for g litch f ree v oltage s caling ? v out range 0.6v to v in ? 0.25v ? short c ircuit and o ver c urrent p rotection ? uvlo and t hermal p rotection ? ic l evel r eliability in a powersoc s olution applications ? automotive applications ? wireless and rf a pplications ? small f orm f actor o ptical m odules ? low noise fpga io and transceivers ? advanced low power processors, dsp, io, memory, video, multimedia engines v out v in 10f 0805 x7r 4.7f 0603 x7r vout pvin avin pgnd agnd vsense ep5358xua vfb vs0 vs1 vs2 enable figure 1 . simplified applications circuit figure 2. highest efficiency in smallest solution size 35 40 45 50 55 60 65 70 75 80 85 90 95 0 100 200 300 400 500 600 efficiency (%) output current (ma) efficiency vs. i out (v in = 5.0v) vout = 3.3v odto v = 5v 14mm 2 10380 june 26, 2015 rev c
EP5358LUA/ep5358hua www.altera.com/enpirion , page 2 ordering information part number package markings t a (c) package description e p 5358 l ua b k xx - 40 to + 105 16 - pin ( 2.5 mm x 2.25 mm x 1. 1 mm) u qfn ep 5358 h ua b n xx - 40 to +105 16 - pin ( 2.5 mm x 2.25 mm x 1.1mm) u qfn evb - e p 5358 x ua qfn evaluation board packing and marking information : www.altera.com/support/reliability/packing/rel - packing - and- marking.html pin assignments (top view) figure 3. ep 5358 l ua pin out diagram (top view) figure 4. ep 5358 h ua pin out diagram (top view) note a : nc pins are not to be electrically connected to each other or to any external signal, ground, or voltage. however, they must be soldered to the pcb. failure to follow this guideline may result in part malfunction or damage. note b : white ?dot? on top left is pin 1 indicator on top of the device package . pin description pin name function pin name function 1, 15, 16 nc(sw) no connect ? these pins are internally connected to the common switching node of the internal mosfets. nc (sw) pins are not to be electrically connected to any external signal, ground, or voltage. however, they must be soldered to the pcb. failure to follow this guideline may result in part malfunction or damage to the device. 2,3 pgnd power ground. connect these pins together and to the ground electrode of the input and output filter capacitors. 4 vfb/nc ep5358 l ua : feed back pin for external divider option. ep5358 h ua : no connect 5 vsense sense pin for preset output voltages. refer to application section for proper configuration . 6 agnd analog ground. this is the quiet ground for the internal control circuitry, and the ground return for external feedback voltage divider 7, 8 vout regulated output voltage. refer to application section for proper layout and decoupling. 9, 10, 11 vs2, vs1, vs0 output voltage select. vs2 = pin 9, vs1 = pin 10 , vs0 = pin 11. ep5358 l ua : selects one of seven preset output voltages or an external resistor divider. ep5358 h ua : s elects one of eight preset output voltages. (refer to section on output voltage select for more details.) nc(sw) pgnd vfb vsense agnd 1 2 3 4 5 6 pvin avin enable vs0 vs2 14 13 12 11 10 9 nc(sw) nc(sw) 16 15 pgnd vout vout vs1 7 8 nc(sw) pgnd nc vsense agnd 1 2 3 4 5 6 pvin avin enable vs0 vs2 14 13 12 11 10 9 nc(sw) nc(sw) 16 15 pgnd vout vout vs1 7 8 10380 june 26, 2015 rev c
ep53 5 8l ua /ep53 5 8h ua www.altera.com/enpirion , page 3 pin name function 12 enable output enable. enable = logic high; disable = logic low 13 avin input power supply for the controller circuitry. 14 pvin input voltage for the mosfet switches. absolute maximum ratings caution : absolute maximum ratings are stress ratings only. functional operation beyond the recommended operating conditions is not implied. stress beyond the absolute maximum ratings may impair device life. exposure to absolute maximum rated conditions for extended periods may affect device reliabili ty. parameter symbol min max units input supply voltage v in - 0. 3 6.0 v voltages on: enable, v sense , v so ? v s2 - 0.3 v in + 0.3 v voltages on: v fb (EP5358LUA) - 0. 3 2. 7 v maximum operating junction temperature t j-abs 150 c storage temperature range t stg - 65 150 c reflow temp, 10 sec, msl3 jedec j - std - 020 c 260 c esd rating (based on h uman b ody m ode ) 2000 v recommended operating conditions parameter symbol min max units input voltage range v in 2. 4 5.5 v operating ambient temperature t a - 40 +10 5 c operating junction temperature t j - 40 + 125 c thermal characteristics parameter symbol typ units thermal resistance: junction to ambient ? 0 lfm ( note 1 ) ja 85 c/w thermal overload trip point t j-tp +155 c thermal overload trip point hysteresis 25 c note 1 : based on a four layer copper board and proper thermal design per jedec eij/jesd51 standards . electrical characteristics note: v in =3 .6 v , minimum and m aximum values are over operating ambient temperature range unless otherwise noted. typical values are at t a = 25c. parameter symbol test conditions min typ max units operating input voltage v in 2.4 5.5 v under voltage lock - out ? v in rising v uvlo_r 2.0 v under voltage lock - out ? v in falling v uvlo_f 1.9 v drop out resistance r do input to output resistance 350 500 m? output voltage range v out ep 5358 l ua (v do = i load x r do ) ep 5358 h ua 0.6 1.8 v in -v do 3.3 v 10380 june 26, 2015 rev c
ep53 5 8l ua /ep53 5 8h ua www.altera.com/enpirion , page 4 parameter symbol test conditions min typ max units operating input voltage range v in 2. 4 5.5 v under voltage lock - out ? v in rising v uvlo_r 2. 0 v under voltage lock - out ? v in falling v uvlo_f 1.9 v drop out resistance r do input to output resistance in 100% duty cycle operation. 350 500 m? output voltage range v out ep5358l ua (v do = i load x r do ) ep5358h ua 0.6 1.8 v in -v do 3.3 v dynamic voltage slew rate (vid change) v slew ep5358l ua ep5358h ua 4 8 v/ms vid preset v out initial accuracy ? v out t a = 25 c , v in = 3.6v; i load = 100ma ; 0.8v v out 3.3 v -2 +2 % line regulation ? v out_line 2.4v v in 5.5 v ; i load = 0a 0.03 %/v load regulation ? v out_load 0a i load 600ma ; v in = 3.6v 0.48 %/a temperature variation ? v out_temp l - 40 c t a + 105 c 24 ppm / c output current range i out 0 600 ma shut - down current i sd enable = low 0.75 a ocp threshold i lim 2.4v v in 5.5 v 0.6v v out 3.3 v 1.25 1.4 a feedback pin voltage initial accuracy v fb t a = 25 c , v in = 3.6v; i load = 100ma ; 0.8v v out 3.3v .588 0.6 0.612 v feedback pin input current i fb note 1 <100 na vs0 - vs2, pin logic low v vslo 0.0 0.3 v vs0 - vs2, pin logic high v vshi 1.4 v in v vs0 - vs2, pin input current i vsx note 1 <100 na enable pin logic low v enlo 0.3 v enable pin logic high v enhi 1.4 v enable pin current i enable note 1 <100 na operating frequency f osc 5 mhz soft start operation soft start slew rate ? v ss ep5358l ua (vid mode) ep5358h ua (vid mode) 2.6 5.2 4 8 5.4 10.8 v/ms v out rise time t rise ep5358l ua vfb mode 146 225 304 s note 1 : parameter guaranteed by design and characterization. 10380 june 26, 2015 rev c
ep53 5 8l ua /ep53 5 8h ua www.altera.com/enpirion , page 5 typical performance curves 40 45 50 55 60 65 70 75 80 85 90 95 100 0 100 200 300 400 500 600 efficiency (%) output current (ma) efficiency vs. i out (v in = 3.3v) vout = 2.5v vout = 1.8v vout = 1.5v vout = 1.2v vout = 1.0v odto v = 3.3v 35 0 5 50 55 60 65 0 5 80 85 0 5 0 100 200 300 00 500 600 outut ut ma efficiency vs. i out (v in = 5.0v) vout = 3.3v vout = 2.5v vout = 1.8v vout = 1.5v vout = 1.2v vout = 1.0v odto v = 5v 0.80 0.85 0.0 0.5 1.000 1.005 1.010 1.015 1.020 0 100 200 300 00 500 600 outut volta v outut ut ma output voltage vs. output current vin = 5.0v vin = 3.3v conditions v out = 1.0v 1.180 1.185 1.190 1.195 1.200 1.205 1.210 1.215 1.220 0 100 200 300 400 500 600 output voltage (v) output current (ma) output voltage vs. output current vin = 5.0v vin = 3.3v conditions v out = 1.2v 1.480 1.485 1.490 1.495 1.500 1.505 1.510 1.515 1.520 0 100 200 300 400 500 600 output voltage (v) output current (ma) output voltage vs. output current vin = 5.0v vin = 3.3v conditions v out = 1.5v 1.780 1.785 1.790 1.795 1.800 1.805 1.810 1.815 1.820 0 100 200 300 400 500 600 output voltage (v) output current (ma) output voltage vs. output current vin = 5.0v vin = 3.3v conditions v out = 1.8v 10380 june 26, 2015 rev c
ep53 5 8l ua /ep53 5 8h ua www.altera.com/enpirion , page 6 typical performance curves (continued) 2.480 2.485 2.490 2.495 2.500 2.505 2.510 2.515 2.520 0 100 200 300 400 500 600 output voltage (v) output current (ma) output voltage vs. output current vin = 5.0v vin = 3.3v conditions v out = 2.5v 3.280 3.285 3.290 3.295 3.300 3.305 3.310 3.315 3.320 0 100 200 300 400 500 600 output voltage (v) output current (ma) output voltage vs. output current vin = 5.0v conditions v out = 3.3v 0.980 0.985 0.990 0.995 1.000 1.005 1.010 1.015 1.020 2.5 3 3.5 4 4.5 5 output voltage (v) input voltage (v) output voltage vs. input voltage load = 600ma load = 0a odto v outo = 1.0v 1.180 1.185 1.10 1.15 1.200 1.205 1.210 1.215 1.220 2.5 3 3.5 .5 5 outut volta v ut volta v output voltage vs. input voltage load = 600ma load = 0a odto v outo = 1.2v 1.80 1.85 1.0 1.5 1.500 1.505 1.510 1.515 1.520 2.5 3 3.5 .5 5 outut volta v ut volta v output voltage vs. input voltage load = 600ma load = 0a odto v outo = 1.5v 1.80 1.85 1.0 1.5 1.800 1.805 1.810 1.815 1.820 2.5 3 3.5 .5 5 outut volta v ut volta v output voltage vs. input voltage load = 600ma load = 0a odto v outo = 1.8v 10380 june 26, 2015 rev c
ep53 5 8l ua /ep53 5 8h ua www.altera.com/enpirion , page 7 typical performance curves (continued) 2.480 2.485 2.490 2.495 2.500 2.505 2.510 2.515 2.520 3 3.5 4 4.5 5 output voltage (v) input voltage (v) output voltage vs. input voltage load = 600ma load = 0a odto v outo = 2.5v 3.200 3.220 3.20 3.260 3.280 3.300 3.320 3.30 3.360 3.380 3.00 5 5.1 5.2 5.3 5. 5.5 outut volta v ut volta v output voltage vs. input voltage load = 600ma load = 0a odto v outo = 3.3v 0.80 0.0 1.000 1.010 1.020 1.030 50 30 10 10 30 50 0 0 110 outut volta v at tatu output voltage vs. temperature load = 600ma load = 0a conditions v in = 5.0v v out_nom = 1.0v 0.980 0.990 1.000 1.010 1.020 1.030 -50 -30 -10 10 30 50 70 90 110 output voltage (v) ambient temperature ( c) output voltage vs. temperature load = 600ma load = 0a conditions v in = 3.3v v out_nom = 1.0v 1.780 1.790 1.800 1.810 1.820 1.830 1.840 -50 -30 -10 10 30 50 70 90 110 output voltage (v) ambient temperature ( c) output voltage vs. temperature load = 600ma load = 0a conditions v in = 3.3v v out_nom = 1.8v 1.780 1.790 1.800 1.810 1.820 1.830 1.840 -50 -30 -10 10 30 50 70 90 110 output voltage (v) ambient temperature ( c) output voltage vs. temperature load = 600ma load = 0a conditions v in = 5.0v v out_nom = 1.8v 10380 june 26, 2015 rev c
ep53 5 8l ua /ep53 5 8h ua www.altera.com/enpirion , page 8 typical performance curves (continued) 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 55 60 65 70 75 80 85 90 95 100 105 maximum output current (a) ambient temperature ( c) no de - rating (v in = 3.3v) vout = 1.8v vout = 2.5v conditions v in = 3.3v t jmax = 125 c no de - rating (v in = 5v) vout = 2.5v vout = 3.3v conditions v in = 5.0v t jmax = 125 c 10380 june 26, 2015 rev c
ep53 5 8l ua /ep53 5 8h ua www.altera.com/enpirion , page 9 typical performance characteristics vout (ac coupled) output ripple at 20mhz bandwidth conditions vin = 5v vout = 1.2v iout = 500ma vout (ac coupled) output ripple at 20mhz bandwidth conditions vin = 5v vout = 3.3v iout = 500ma vout (ac coupled) output ripple at 20mhz bandwidth conditions vin = 3.3v vout = 1.8v iout = 500ma vout (ac coupled) output ripple at 20mhz bandwidth conditions vin = 3.3v vout = 1.2v iout = 500ma enable enable power up conditions vin = 5v vout = 3.3v (vid mode) iout = 10ma vout enable enable power down conditions vin = 5v vout = 3.3v (vid mode) iout = 10ma vout 10380 june 26, 2015 rev c
ep53 5 8l ua /ep53 5 8h ua www.altera.com/enpirion , page 10 typical performance characteristics (continued) enable enable power up conditions vin = 5v vout = 3.3v (vid mode) iout = 500ma vout enable enable power down conditions vin = 5v vout = 3.3v (vid mode) iout = 500ma vout vout (ac coupled) load transient from 0 to 500ma conditions vin = 5v vout = 1.2v load vout (ac coupled) load transient from 0 to 500ma conditions vin = 3.3v vout = 1.8v load 10380 june 26, 2015 rev c
ep53 5 8l ua /ep53 5 8h ua www.altera.com/enpirion , page 11 functional block diagram dac switch vref (+) (-) error amp vsense vfb vout package boundry p-drive n-drive uvlo thermal limit current limit soft start sawtooth generator (+) (-) pwm comp pvin enable pgnd logic compensation network nc(sw) voltage select vs0 vs1 avin vs2 agnd figure 5: functional block diagram 10380 june 26, 2015 rev c
ep53 5 8l ua /ep53 5 8h ua www.altera.com/enpirion , page 12 functional description functional overview the ep5358x ua requires only 2 small mlcc capacitors for a complete dc - dc converter solution. the device integrates mosfet switches, pwm controller, gate - drive, compensation, and inductor into a tiny 2.5mm x 2.25mm x 1.1mm micro - qfn package. advanced package design, al ong with the high level of integration, provides very low output ripple and noise. the ep5358x ua uses voltage mode control for high noise immunity and load matching to advanced 90nm loads. a 3 - pin vid allows the user to choose from one of 8 output voltage settings. the ep5358x ua comes with two vid output voltage ranges. the ep5358h ua provides v out settings from 1.8v to 3.3v, the ep5358l ua provides vid settings from 0.8v to 1.5v, and also has an external resistor divider option to program output setting over the 0.6v to v in - 0.25v range. the ep5358x ua provides the industry?s highest power density of any 600ma dcdc converter solution. the key enabler of this revolutionary integration is altera?s proprietary power mosfet technology. the advanced mosfet switches are implemented in deep - submicron cmos to supply very low switching loss at high switching frequencies and to allow a high level of integration. the semiconductor process allows seem - less integration of all switching, control, and compensation circu itry. the proprietary magnetics design provides high - density/high - value magnetics in a very small footprint. altera enpirion magnetics are carefully matched to the control and compensation circuitry yielding an optimal solution with assured performance ov er the entire operating range. protection features include under - voltage lock - out (uvlo), over - current protection (ocp), short circuit protection, and thermal overload protection. integrated inductor: low - noise low - emi the ep5358x ua utilizes a proprietary low loss integrated inductor. the integration of the inductor greatly simplifies the power supply design process. the inherent shielding and compact construction of the integrated inductor reduces the conducted and radiated noise that can couple into the traces of the printed circuit board. further, the package layout is optimized to reduce the electrical path length for the high di/dt input ac ripple currents that are a major source of radiated emissions from dc - dc converters. the integrated inductor provides the optimal solution to the complexity, output ripple, and noise that plague low power dcdc converter design. control matched to sub 90nm loads the ep5358x ua utilizes an integrated type iii compensation network. voltage mode control is inherently impedance matched to the sub 90nm process technology that is used in today?s advanced ics. voltage mode control also provides a high degree of noise immunity at light load currents so that low ripple and high accuracy are maintained over the entire load range. the very high switching frequency allows for a very wide control loop bandwidth and hence excellent transient performance. soft start internal soft start circuits limit in - rush current when the device starts up from a power down condition or when the ?enable? pin is asserted ?high?. digital control circuitry limits the v out ramp rate to levels that are safe for the power mosfets and the integrated inductor. the ep5358h ua has a soft - start slew rate that is twice that of the ep5358l ua . when the ep535 8lua is configured in external resistor divider mode, the device has a fixed vout ramp time. therefore, the ramp rate will vary with the output voltage setting. output voltage ramp time is given in the electrical characteristics table. excess bulk capacitance on the output of the device can cause an over - current condition at startup. the maximum total capacitance on the output, including the output filter capacitor and bulk and decoupling capacitance, at the load, is given as: ep5358l ua : c out_total _max = c out_filter + c out_bulk = 230 f ep5358h ua : c out_total_max = c out_filter + c out_bulk = 115 f ep5358l ua in external divider mode: c out_total_max = 2.086x10 -4 /v out farads the above numbers and formula assume a no load 10380 june 26, 2015 rev c
ep53 5 8l ua /ep53 5 8h ua www.altera.com/enpirion , page 13 condition. over current/short circuit protection the current limit function is achieved by sensing the current flowing through a sense p - mosfet which is compared to a reference current. when this level is exceeded the p - fet is turned off and the n - fet is turned on, pulling v out low. this condition is maintained for approximately 0.5ms and then a normal soft start is initiated. if the over current condition still persists, this cycle will repeat. under voltage lockout during initial power up an under voltage lockout circuit will hold - off the switching circuitry until the input voltage reaches a sufficient level to insure proper operation. if the voltage drops below the uvlo threshold the lockout circuitry will again disable the switching. hysteresis is included to prevent chattering between states. enable the enable pin provides a means to shut down the converter or enable normal operation. a logic low will disable the converter and cause it to shut down. a logic high will enable the converter into normal operation. note: the enab le pin must not be left floating. thermal shutdown when excessive power is dissipated in the chip, the junction temperature rises. once the junction temperature exceeds the thermal shutdown temperature the thermal shutdown circuit turns off the converter output voltage thus allowing the device to cool. when the junction temperature decreases by 15c, the device will go through the normal startup process. 10380 june 26, 2015 rev c
ep53 5 8l ua /ep53 5 8h ua www.altera.com/enpirion , page 14 application information v out v in 10f 0805 x7r 4.7f 0603 x7r vout pvin avin pgnd agnd vsense ep5358hua vs0 vs1 vs2 enable figure 6. ep5358hua application circuit v out v in 10f 0805 x7r 4.7f 0603 x7r vout pvin avin pgnd agnd vsense EP5358LUA vfb vs0 vs1 vs2 enable figure 7. EP5358LUA application circuit output voltage programming the ep5358x ua utilizes a 3 - pin vid to program the output voltage value. the vid is available in two sets of output vid programming ranges. the vid pins should be connected either to avin or to agnd to avoid noise coupling into the device. the ?low? range is optimized for low voltage applications. it comes with preset vid settings ranging from 0.80v and 1.5v. this vid set also has an external divider option. to specify this vid range, order part number ep5358l ua . the ?high? vid set provides output voltage setting s ranging from 1.8v to 3.3v. this version does not have an external divider option. to specify this vid range, order part number ep5358h ua . internally, the output of the vid multiplexer sets the value for the voltage reference dac, which in turn is connected to the non - inverting input of the error amplifier. this allows the use of a single feedback divider with constant loop gain and optimum compensation, independent of the output voltage selected. note: the vid pins must not be left floating. ep5358l low vid range programming the ep5358l ua is designed to provide a high degree of flexibility in powering applications that require low v out settings and dynamic voltage scaling (dvs). the device employs a 3 - pin vid architecture that allows the user to choose one of seven (7) preset output voltage settings, or the user can select an external voltage divider option. the vid pin settings can be changed on the fly to implement glitch - free voltage scaling. table 1 . ep5358l ua vid voltage select settings table 1 shows the vs2 - vs0 pin logic states for the ep5358l ua and the associated output voltage levels. a logic ?1? indicates a connection to avin or to a ?high? logic voltage level. a logic ?0? indicates a connection to agnd or to a ?low? logic voltage level. these pins can be either hardwired to avin or agnd or alternatively can be driven by standard logic levels. logic levels are defined in the electrical characteristics table. any level between the logic high and logic low is indeterminate. ep5358l ua external voltage divider the external divider option is chosen by connecting vid pins vs2 - vs0 to v in or a logic ?1? or ?high?. the ep5358l ua uses a separate feedback pin, v fb , when using the external divider. v sense must be connected to v out as indicated in f igure 8. vs2 vs1 vs0 vout 0 0 0 1.50 0 0 1 1.45 0 1 0 1.20 0 1 1 1.15 1 0 0 1.10 1 0 1 1.05 1 1 0 0.8 1 1 1 ext 10380 june 26, 2015 rev c
ep53 5 8l ua /ep53 5 8h ua www.altera.com/enpirion , page 15 v out v in 10f 0805 x7r 4.7f 0603 x7r vout pvin avin pgnd agnd vsense EP5358LUA vfb vs0 vs1 vs2 enable r a r b figure 8. ep5358lu a u sing external d ivider the output voltage is selected by the following formula: ( ) rb ra out vv += 16.0 r a must be chosen as 237k? to maintain loop gain. then r b is given as: ? ? = 6.0 102.142 3 out b v x r v out can be programmed over the range of 0.6v to (v in ? 0.25v). note: dynamic voltage scaling is not allowed between internal preset voltages and external divider. ep5358 h ua high vid range programming the ep5358h ua v out settings are optimized for higher nominal voltages such as those required to power io, rf, or ic memory. the preset voltages range from 1.8v to 3.3v. there are eight (8) preset output voltage settings. the ep5358h ua does not have an external divider option. as with the ep5358l ua , the vid pin settings can be changed while the device is enabled. table 2 shows the vs0 - vs2 pin logic states for the ep5358h ua and the associated output voltage levels. a logic ?1? indicates a connection to avin or to a ?high? logic voltage level. a logic ?0? indicates a connection to agnd or to a ?low? logic voltage level. these pins can be either hardwired to avin or agnd or alternatively can be driven by standard logic levels. logic levels are defined in the electrical characteristics table. any level between the logic high and logic low is indeterminate. these pins must not be left floating. table 2: ep5358h ua vid voltage select settings custom vid setting adjustment v out v in 10f 0805 x7r 4.7f 0603 x7r vout pvin avin pgnd agnd vsense ep5358xua vfb vs0 vs1 vs2 enable 5pf r s figure 9. ep5358x ua with rc inserted in vsense path to modify vid output voltages. it is possible to adjust vout for a given vid setting by inserting a parallel rc combination in the vsense path as shown in f igure 9. the capacitor value is 5.0pf to ensure stability. note that the value of vout can only be increased from its nominal setting (vout new >vout old ): for ep5358l ua : kohms vout vout rs old new l ? ? ? ? ? ? ? = 1 *711 for ep5358h ua : kohms vout vout rs old new h ? ? ? ? ? ? ? = 1 *356 vout new is the desired ?new? vout. vs2 vs1 vs0 vout 0 0 0 3.3 0 0 1 3.0 0 1 0 2.9 0 1 1 2.6 1 0 0 2.5 1 0 1 2.2 1 1 0 2.1 1 1 1 1.8 10380 june 26, 2015 rev c
ep53 5 8l ua /ep53 5 8h ua www.altera.com/enpirion , page 16 vout old is the vid table output voltage. for a given rs value, the vout new for vid settings is determined by the following equations: ep5358l ua : volts rs vout vout l old new ? ? ? ? ? ? + ? ? ? ? ? ? = 1 711 ep5358h ua : volts rs vout vout h old new ? ? ? ? ? ? + ? ? ? ? ? ? = 1 356 note: the amount of adjustment is limited to approximately 15% of the nominal vid setting. note: adjusting vout using this method will increase the tolerance of the output voltage. the larger the adjustment, the greater the increase in tolerance. power-up/down during power - up, enable should not be asserted before pvin, and pvin should not be asserted before avin. the pvin should never be powered when avin is off. during power down, the avin should not be powered down before the pvin. tying pvin and avin or all three pins (avin, pvin, enable) together during power up or power down meets th ese requirements. the ep5358xua supports startup into a pre - biased output of up to 1.5v. the output of the ep5358xua can be pre - biased with a voltage up to 1.5v when the ep5358xua is first enabled. input filter capacitor the input capacitor requirement is a minimum of 4.7f 0603 x7r mlcc. y5v or equivalent dielectric formulations lose capacitance with frequency, bias, and with temperature, and are not suitable for switch - mode dc - dc converter input filter applications. output filter capacitor the output filter capacitor requirement is a minimum of 10f 0805 x7r mlcc. ripple performance can be improved by using 2x10f 0805 x7r mlcc capacitors (for any allowed vin). the maximum output filter capacitance next to the output pins of the device is 60f low esr mlcc capacitance. vout has to be sensed at the last output filter capacitor next to the ep5358x ua . additional bulk capacitance for decoupling and bypass can be placed at the load as long as there is sufficient separation between the vout sense point and t he bulk capacitance. excess total capacitance on the output (output filter + bulk) can cause an over - current condition at startup. refer to the section on soft - start for the maximum total capacitance on the output. the output capacitor must use a x5r or x7r or equivalent dielectric formulation. y5v or equivalent dielectric formulations lose capacitance with frequency, bias, and temperature and are not suitable for switch - mode dc - dc converter output filter applications. 10380 june 26, 2015 rev c
ep53 5 8l ua /ep53 5 8h ua www.altera.com/enpirion , page 17 thermal considerations thermal considerations are important power supply design facts that cannot be avoided in the real world. whenever there are power losses in a system, the heat that is generated by the power dissipation needs to be accoun ted for. the enpirion powersoc helps alleviate some of those concerns. the enpirion e p 5358x ua dc- dc converter is packaged in a 2.5 x 2.25 x 1.1 mm 16- pin qfn package. the recommended maximum junction temperature for continuous operation is 1 25 c. continuous operation above 1 25 c may reduce long - term reliability. the device has a thermal overload protection circuit designed to turn off the device at an approximate junction temperature value of 1 55 c. the following example and calculations illustrate the thermal performance of the ep5358x ua . example: v in = 5v v out = 3.3v i out = 600ma first calculate the output power. p out = 3.3v x 600ma = 1.98 w next, determine the input power based on the efficiency () shown in figure 10 . figure 10 . efficiency vs. output current for v in = 5v, v out = 3.3v at 600ma , 91 % = p out / p in = 91 % = 0. 91 p in = p out / p in 1.98 w / 0. 91 2.18 w the power dissipation (p d ) is the power loss in the system and can be calculated by subtracting the output power from the input power. p d = p in ? p out 2.18 w ? 1.98 w 0.2 w with the power dissipation known, the temperature rise in the device may be estimated based on the theta ja value ( ja ). the ja parameter estimates how much the temperature will rise in the device for every watt of power dissipation. the e p5 3 58x ua has a ja value of 85 oc/w without airflow. determine the change in temperature (t) based on p d and ja . t = p d x ja t 0. 2 w x 85 c/w 17 c the junction temperature (t j ) of the device is approximately the ambient temperature (t a ) plus the change in temperature. we assume the initial ambient temperature to be 25c. t j = t a + t t j 25c + 17 c 42 c the maximum operating junction temperature (t jmax ) of the device is 125c, so the device can operate at a higher ambient temperature. the maximum ambient temperature (t amax ) allowed can be calculated . t amax = t jmax ? p d x ja 125c ? 17 c 108c the maximum ambient temperature (before de - rating) the device can reach is 84 c given the input and output conditions. note that the efficiency will be slightly lower at higher temperatures and this calculation is an estima te. 35 40 45 50 55 60 65 70 75 80 85 90 95 0 100 200 300 400 500 600 efficiency (%) output current (ma) efficiency vs. i out (v in = 5.0v) vout = 3.3v odto v = 5v 91% 10380 june 26, 2015 rev c
ep53 5 8l ua /ep53 5 8h ua www.altera.com/enpirion , page 18 layout recommendation figure 1 1 shows critical components and layer 1 traces of a recommended minimum footprint ep5358l ua /ep5358h ua layout with enable tied to v in . alternate enable configurations, and other sma ll signal pins need to be connected and routed according to specific customer application. please see the gerber files on the altera website www.altera.com/enpirion for exact dimensions and other layers. please refer to figure 11 while reading the layout recommendations in this section. recommendation 1: input and output filter capacitors should be placed on the same side of the pcb, and as close to the ep5358 ua package as possible. they should be connected to the device with very short and wide traces. do not use thermal reliefs or spokes when connecting the capacitor pads to the respective nodes. the +v and gnd traces between the capacitors and the ep5358 ua sho uld be as close to each other as possible so that the gap between the two nodes is minimized, even under the capacitors. recommendation 2: input and output grounds are separated until they connect at the pgnd pins. the separation shown on figure 11 between the input and output gnd circuits helps minimize noise coupling between the converter input and output switching loops. recommendation 3: the system ground plane should be the first layer immediately below the surface layer. this ground plane should be co ntinuous and un - interrupted below the converter and the input/output capacitors. please see the gerber files on the altera website www.altera.com/enpirion . figure 1 1: top pcb lay er critical components and copper for minimum footprint recommendation 4 : multiple small vias should be used to connect the ground traces under the device to the system ground plane on another layer for heat dissipation. the drill diameter of the vias shou ld be 0.33mm, and the vias must have at least 1 oz. copper plating on the inside wall, making the finished hole size around 0.20 - 0.26mm. do not use thermal reliefs or spokes to connect the vias to the ground plane. it is preferred to put these vias under t he capacitors along the edge of the gnd copper closest to the +v copper. please see figure 11 . these vias connect the input/output filter capacitors to the gnd plane and help reduce parasitic inductances in the input and output current loops. if the vias cannot be placed under c in and c out , then put them just outside the capacitors along the gnd. do not use thermal reliefs or spokes to connect these vias to the ground plane. recommendation 5 : avin is the power supply for the internal small - signal control circuits. it should be connected to the input voltage at a quiet point. in figure 11 this connection is made at the input capacitor close to the v in connection. 10380 june 26, 2015 rev c
ep53 5 8l ua /ep53 5 8h ua www.altera.com/enpirion , page 19 recommended pcb footprint figur e 1 2 . ep 5358 x ua pcb footprin t ( top view) 10380 june 26, 2015 rev c
ep53 5 8l ua /ep53 5 8h ua www.altera.com/enpirion , page 20 package and mechanical figur e 1 3 . ep 5358 l ua package dimensions (bottom view) 10380 june 26, 2015 rev c
ep53 5 8l ua /ep53 5 8h ua www.altera.com/enpirion , page 21 figure 1 4 . ep5358 h ua package dimensions (bottom view) packing and marking information : www.altera.com/support/reliability/packing/rel - packing - and- marking.html contact information altera corporation 101 innovation drive san jose, ca 95134 phone: 408 - 544 - 7000 www.altera.com ? 201 4 altera corporation ? confidential. all rights reserved. altera, arria, cyclone, enpirion, hardcopy, max, megacore, nios, quartus and stratix words and logos are trademarks of altera corporation and registered in the u.s. patent and trademark office and in other countries. all other words and logos identified as trademarks or service marks are the property of their respective holders as described at www.altera.com/common/legal.html. al tera warrants performance of its semiconductor products to current specifications in accordance with altera's standard warranty, but reserves the right to make changes to any products and services at any time without notice. altera assumes no responsibility or liability arising out of the application or use of any information, pr oduct, or service described herein except as expressly agreed to in writing by altera. altera customers are advised to obtain the latest version of device specifications before relying on any published information and before placing orders for products or services. 10380 june 26, 2015 rev c

▲Up To Search▲

Price & Availability of EP5358LUA

	To Download EP5358LUA Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .